Frequently Asked Questions
A vibration system is an indispensable solution, especially for facilities requiring high mechanical strength. Hot and cold rooms of all kinds of meat, milk, fish, beverage, and bakery producers are a time-saving system that solves the robust and long-lasting floor needs of their rebel and caustic environments, thanks to the application of 400 doses of thick bed mortar and ceramics on the same day.
Our products are produced in Turkey. It is Turkish Goods.
Advantages of anti-acid industrial tiles according to the epoxy floor;
Always the same thickness,
Density high surface,
The surface is an integral part of ceramic,
Color does not change, easy to clean,
Point pressure may be higher – load distribution is more appropriate,
Durable up to 100 C°,
It doesn’t hurt health,
Respectful of nature and longer-lasting (> 15 years).
They increase the strength of the tile to stick to the floor by increasing the surface area.
Hygienic skirting can be produced in the colors requested, depending on the order quantity.
Applications can be made while factories continue to work, but there are some difficulties. The region to be implemented must be bested to work. Depending on the area’s availability to be done, the end times of the work may also vary.
Stainless tile is used in cold or hot room door crossings with high-temperature differentiation and heavy traffic on the ground and in combinations of different types of materials, loading with heavy load traffic to protect building main dilation profiles, elevator door fronts, ramps. It is preferred to prevent breakages and cracks due to heat differences in room and door crossings. It is especially preferable where there is heavy load traffic.
Hygienic stainless kerb, stainless surface, easy to clean, and protects panels, walls, and columns in all areas requiring hygiene. They are products with smooth surfaces, resistant to acids and chemicals. Thanks to its radius form, it is easy to clean and reduce bacterial formation. Thanks to the ease of maintenance, they are much more efficient and permanent solutions than alternatives.
Our hygienic panel protective products were assessed according to Turkish Food Codex Food Contact Substances and Ingredients Communiqué 2013/34 and Commission Regulation EU No:10/2011. As a result of the migration tests, it is suitable for the food theme.
To apply our semi-dry screed in anti-acid industrial to the application, a minimum share of ground concrete must be left 10-12 cm (depending on the slope condition).
VSEE Vibration System XW1000 epoxy bonding and W13 liquid epoxy joint filler application system; Vsee system, which is an accepted system on the floors of food facilities in all developed countries, is a specially developed XW1000 with much higher adhesion strength than its counterparts for vibration application method, gel paste type epoxy-based adhesive and epoxy-based W13 liquid joint filler application applied with a machine system.
The XW1000 has much higher adhesion strength than its counterparts, gel paste type epoxy-based adhesive, and epoxy-based W13 liquid joint filler application applied with a machine system.
VSFE Vibration System flex bonding and W13 epoxy joint filler application system.
VSFF Vibration System; flex bonding and flex joint filler application system.
VSEE warranty is 4 years.
Developed for vibration system applications in industrial facilities, gel paste type epoxy-based R2 class are a solvent-free adhesive and multipurpose repair mortar with high adhesion strength.
– High strength, cement-based double component C2TE S1 class flex adhesive.
– CG2 class flex joint sealant.
High strength cement-based, double component C2TE S1 class can be applied with flex adhesive.
The food industry, beverage industry, Shopping Mall & Supermarket, Health, Chemistry, Manufacturing, Cosmetics, Automotive
There is no company in any other country where we are a dealer.
W6 adherence channels are available with conical edges and natural joint provider nails and back adhesion strength enhancer. Surface anti-slip is produced in classes R9, R10, R11, and R12.
They are porous, easy to clean, resistant to acids, chemicals, and do not produce bacteria within them with low water absorption values.
Hexagonal tile is even more resistant to impacts and heavy loads due to its size and form.
– Resistance to low concentration acids and alkali according to ISO 10545-13 standards LA
– Resistance to high concentrations of acids and alkali according to ISO 10545-13 standards HA
– Resistance to household chemicals and swimming pool salts according to ISO 10545-13 standards A
Anti-Acid tiles are resistant to impacts. Its impact strength is 0.87, according to ISO 10545-5 standards.
Light beige, Beige, Yellow, Gray
Available in 18mm, 15mm, 14mm (20×20), and 13.2mm thickness varieties.
The guarantee of anti-acid tiles is 10 years.
Surface anti-slips of anti-acid tiles are produced in grades R9, R10, R11, and R12, according to CEN/TS 16165 DIN 51130 standard.
It can be produced according to the quantity requested.
Thanks to the nails found on the lateral surfaces of anti-acid tiles, a “V” range remains when the ceramics are side by side, and joint cavities are formed naturally during application.
The joint filler you will use may differ depending on the function of the facility you will apply. Epoxy-based, three-component W13 Liquid Epoxy Joint Filler developed for industrial facilities is resistant to acidic environments and is long-lasting. You can easily use it in your food facilities such as meat, milk, fish, and beverages. Favo Anti-Acid ceramics are also suitable for cement-based joint fillers. Due to its structure, cement-based joint fillers have a low resistance to acid, and after a while, abrasions are observed on surfaces exposed to acid. It is suitable for acidic and non-caustic environments of your facilities.
Plant buildings continue to react and work against environmental factors and loads on them. Simultaneously, the vibration system moves in the form of a thick floor combined with the application and the floor covering with 400 Doses of Thick Bed Mortar. It works separately from the floor, with the floor separator placed under the mortar. The buildings’ main dilation lines and the expansion lines applied on the ground are applied to minimize ground damage caused by expansions that may occur against these physical events mentioned or in hot-cold transitions by dividing the entire floor into smaller areas.
The section with spatial or point damage can be cut and changed by our expert team without the rest of the floor is affected.
Because the load carrying strength is low on large-sized tiles, small sizes are especially hexagonal, capable of carrying higher loads.
Problems you may encounter in resin-based products;
– Variable thickness, can make local collapses,
– Bacteria can produce,
– Pores may form during the application,
– Non-slip value may not be possible at some times,
– Colors may change over time, difficult to clean,
– Can be damaged at point pressure, sensitive to hot and cold changes,
– May damage health according to the materials it has,
– Because it is a chemical product, its lifespan can last 4-6 years, requiring renewal.
Anti-Acid is tile;
– Always the same thickness, flat and non-slip level.
– High-density surface is an integral part of ceramic,
– The color does not change.
– Easy to clean, and point pressure is better suitable for heavy load distribution.
Resistant to up to 100 degrees, no health damage, respectful nature, and long-lasting floor covering material.
Yes, we have such a comparison table. When you contact us, our Marketing department will provide you with this.
There is no need for repair and refurbishment for a long time in the methods we have implemented. Therefore, they are longer-lasting floors.
In local supply, we demand from the employer because the customer can make purchases at more economical prices.
Yes, test results and videos are available. You can contact us for your requests on the subject.
Can you give me a document that they’re food-safe material that I can show you when they ask during the checks?
As with any material, these products can be cleaned and cared for with cleaning materials that do not contain solvent acids. Local repairs can be made. We can provide you with a document on food safety. Because epoxies do not contain solvents, they do not cause any problems in foods or food production facilities.
Our products are not PVC. We produce polymer materials that we make a special formulation. Our products are suitable for food contact (illustration) tests. Therefore, all food production facilities, sales areas, health sector, etc., can be applied in all areas requiring hygiene.
Our products and application systems can be used in all hygiene areas. The method we apply does not allow bacteria to reproduce at edge corners and panel bottoms. Of course, you can use our products.
In the case of demand, we can make a special production.
Neutral Silicone used in insulation; What should we pay attention to in cleaning so that the ability not to produce bacteria, fungi, mold is not lost?
As long as cleaning is done with appropriate chemicals, no fungi or molds are allowed on the surface.
Panel protectors and pontoons mounting guides and videos are available on our website. A special leaflet is available for each product that specifies the stages.
Yes, the application requires the necessary knowledge of machinery, equipment, and mastery.
Panel protectors are +15 degrees, and the area to be applied should not be wet. – At (minus) degrees, it is not very possible to practice in cold rooms.
Epoxy adhesive is used for bonding purposes in many sectors and is used for filling purposes. In the construction industry, ceramics and many similar products can be used as bonding and joint filling.
Epoxies with different formulations can be produced in heat environments or short and long-term hot water spills. Accordingly, the temperature strength of epoxy adhesives varies.
Air temperature – drying time varies between 8 and 48 hours according to ambient temperature. Vibroser XW1000, W65, W065, and Liquid 13 epoxy products are products used for adhesive and joint filling in industrial facilities. These products complete the hardening process between 8 and 24 hours according to the heat in the environment.